PCT-1000 Programmable PreheaterMore Heat, Lower Temperatures for Faster, Higher Quality ResultsThe new PCT-1000 is a programmable preheater that provides users exceptional ability to increase heat capacity with highly controlled thermal output. The preheater is ideal for aiding high thermal demand applications including lead-free, multi-layer boards and large ground planes. The PCT-1000 can be used in a variety of processes including soldering, desoldering, SMD rework operations and, with its added heat capacity, will provide faster production rates while lowering overall process ControlsWith four programmable heating zones and one cooling zone, users select time and temperature targets, creating a preheat thermal PCT-1000 features an advanced heat control function where the temperature is controlled either at the heater output (internal) or at the board (external). The "external" control function uses a thermocouple which can be placed on the board or a component. The external control function enables users to heat with high levels of assurance; preventing such undesirable effects as underside component reflow, thermal shock to sensitive components and damaging peak thermal profiling with independent time and temperature selects internal or external PCT-1000 Powerful Heating Improves ProductivityPCT-1000 is equipped with the highly advanced heater design found on sophisticated OK International rework systems. Its convection heater creates a vortex effect that efficiently directs and concentrates heat. This, coupled with the precise feedback control and thermal profiling capability, establish the PCT-1000 as a powerful, precise benchtop solution for increasing Operation and Profile StorageThe PCT-1000 is easy-to-use with clearly marked controls. The front panel features a 20 X 4 LCD display and 3 input buttons. Step by step programming makes profile creation simple and straight forward. The system stores up to 50 thermal profiles plus one default start up , Flexible Board HoldersWhile the PCT-1000 can be used with or without a board holder, users often need a quick and flexible way to position a board over the preheater. The new BH-1000 board holder consists of posts and rails and is a highly flexible system. It has two sets of post-rail assemblies (two posts, one rail per assembly). Two sliding clips are mounted on each rail and require minimal board-edge space to clamp the board. The post-rail assemblies can be located as close as 12 mm (1/2") to virtually any distance apart. Additionally, each post-rail system can be converted to a stand-alone post-pin configuration with removal of the rails and by adding the threaded pins (shown right). These pins can be used for holding board tooling holes or for board Features & Benefits• Adds heat capacity and enables lower process temperatures• Increases through-put and reliability of soldering, desoldering and SMD rework processes• Four-zone programmable settings for time and temperature to create optimum thermal profiles for varying application demands• Storage for up to fifty users defined profiles for quick, easy set-up• User selectable control of heating at source (internal) or at target (external)• Controlled cool-down eliminates thermal shock to PCB and components• System safety feature automatically shuts off heating when fan is stopped• High efficiency vortex heater design maximizes ramp to temperature for increased productivityPart NumberDescriptionPCT-1000Programmable Preheater, 350W convection;Type-K T/C kit, foot switch, power cord, User Manual, Advanced User GuidePCT-FS1PCT-1000 Foot switchBH-1000Post-Rail Board Holder system; four posts, two rails with sliding clips, four support pins, flat-head support (screw)BH-SP1000Single Post Board Support; post with height adjustment, four support pinsBH-PK1000Support Pin Kit; four support pins, flat-head support screwBH-RK1000Board Holder Rail Kit; two 300mm rails, four support pinsHeater Rating:900WInput:100-240 VAC, 50/60 HzTemperature Range:50°C to 350°C (120°F to 660°F)Temperature Control:Type K Thermocouple feedback with users selectable source (internal) or target (external) control External: includes two Type K inputsAir Flow:Fixed at 19cfm (538 l/minute)Programs:Storage for fifty (50) thermal profilesApprovals:CE, cTUVusMaximum time per zone:300 seconds2 options: post-rail system (shown above)or post-pin systems (shown below)PCT-1000 with foot switchPCT-1000 External Type K thermocouple inputs
所有评论仅代表网友意见,与本站立场无关。